Sunday, 15 November 2026

Common issues with Bernina 1950s and 60s models (530, 730, 7xx etc)

Berninas really are the best sewing machines ever made, and are certainly the best central bobbin machines by far. They are quieter, smoother and more reliable than any other CB I've ever seen.

The 830 and other 8xx machines are the best of the best, but the 730 and other 7xx machines are pretty much the same. As with all machines, they have their issues. The one that springs to mind for all of these is the camstack gear, which Bernina decided was best made from nylon. Nylon was a good choiceover what they used before that (midway through the 530 they swapped from a more reliable plastic) but as most of us know, after about 40 years they crack and have to be replaced. Replacement is relatively easy and inexpensive (although you need to pick a good quality one - they're not all well made) and this has been documented quite well. 

I will instead be going over the two more common issues I see in my shop.

1. The needle position won't move or can move too easily, and

2. The buttonhole mechanism will not move.

Both seized components are here

The solution to both of these is not too complicated. Regardless of whether you have one or both of these issues, repair involves the same procedure.

The four important components for this job

You must set the zig-zag control to maximum then remove the needle position knob. To do this, loosen the nut marked with a red 1.

Remove the knob by twisting and pulling at the same time. Note that there is a large spring washer on the front, between the knob and the machine body. The internal mechanism (marked 3) can be allowed to drop out of the way.

Next, loosen slightly the screw marked with a red 2. You should now be able to remove the zig-zag control which contains the buttonhole mechanism, which is a zig-zag limiter. 

If you're doing this because you're having trouble with the needle position you won't be able to remove the plunger (marked 4), but if by some miracle it moves freely, remove the plunger as well as the spring behind it.

Assuming the plunger is seized, you need to turn your attention to the front. Remove the three screws that are holding the zig-zag label on. It is also holding the plunger and spring. Once you have removed this, carefully remove everything. If you might not remember where everything goes, take pictures with your phone.

With everything out, you need to apply some heat to the seized component/s to loosen them Don't be tempted to force anything with tools. Remove the spring before you start.

Components in boiling water

Put the zig-zag control and the needle stop into a cup and pour very hot or boiling water into the cup, covering the parts. Wait for a couple of minutes then remove the parts one at a time. The buttonhole mechanism should now be soft enough that you can move it with your hands. Apply some solvent if it starts to move (methylated spirits and mineral turperntine), and move it back and forth. After several of these, it should be very easy to move and you will start hearing a click when it goes back and forth. Now, dry it (I use compressed air) then apply a drop or two of SMO (sewing machine oil) and work it in. Pat yourself on the back because that's one job done.

Remove the plunger and use your bench to try and push the plunger into the housing. Once you can do this, apply solvents and use something reasonable strong and pointed to pus it out again. Once it gives a little, the solvent makes it much easier very quickly. Again, apply a drop of SMO, work it in, and reassemble.

Reassembly is actually pretty easy. You can put the spring and plunger in after the housing, because it's no longer stuck. Be careful not to lose the spring.

Make sure you have the spring washer on and push the zig-zag control before tightening the screw. Setting the zig-zag in the right spot is made easy because the mechanism needs to be at the bottom of its travel at the zero setting. If you have chosen to put the spring and plunger in afterthe zig-zag control, do it now. The part marked 3 can now be replaced and tightened and you're finished. If you find it hard to set the zig-zag and needle position, loosen it off just enough for an adjustment. 

Sunday, 20 September 2026

Swiss made Elna SU and Blue Top Supermatic repairs

Elna are now owned by Janome. I'm hoping that it's false, but I was told by an ex Elna dealer that when Janome bought the brand, they immediately dumped (destroyed) all the spare parts for the Swiss made machines and declared that they wouldn't support the machines at all. 
Thankfully, the parts that fail are usually simple gears and are still being made well in places such as Taiwan.
You can read about the history of Elna at ISMACS but they are as amazing as Berninas are and for the same reasons: The high quality of the components and the tight tolerances. Necchi had the latter, but failed in the quality of the component steel (it was not nearly as durable as it could have been).
So, the best sewing machine ever made is not an Elna (it's Bernina's 830 Record - ask any sewing machine mechanic), but in second place is the 1970s SU. This machine is almost identical to the 1960s version (Supermatic, some were just labelled Super but the top is always blue) but Elna tweaked a few small things and got a very slightly smoother machine. They are both called 62C by Elna and they're both fantastic.
I get a lot of Elnas into the shop, and the most common problem by far is that the needle position wheel is seized. Also, often the balance wheel is slipping.

Repairing the two most common problems with a
62C 

Needle Position Seized

Even if you think you don't care about the needle position wheel, it is important if you want to take advantage of the no-turn buttonhole feature (it must be on the left setting).
The solution to this is to work solvents in to dissolve the dried stuff that's causing it to be glued. Here is what I do. You will need a bottle of methylated spirits with a spray top.
If you can move the wheel but it is very stiff, you can try this:
Remove the top of the machine.
Place the machine on its side with the needlebar up, and you see the view below.
The area in red, under the wheel
Spray methylated spirit at the bottom of the needle position wheel. Don't get any on the red or black printed indicator part or they will dissolve.
Move the wheel back and forth. You might need to do this for more than 15 minutes, but it will get easier as you go. I put a piece of fabric between my fingers and the wheel to prevent blisters. You will need to reapply the methylated spirits every few cycles. You're finished when it is very easy to move with one finger. It should 'snap' into the centre needle position.
If you can't move it at all, your next step is to heat the seized area. I have a heat source as part of a soldering station and use that. Before I had that I used a heat gun and before that a hairdryer. You must approach heating this with the knowledge that if you are careless, you will melt the position wheel. Try not to do this. Putting the whole machine in a hot car is anopther good option.
After heating the same area (the underneath part of the position wheel), it should be possible to move the wheel. Now, spray the methylated spirits, move wheel, metho, move, repeat.
When it is completely freed as above, you need to test it again when the temperature of the metal has become even with the room. If the gunk that was gluing it is still there, being warm would change its viscosity. If it's still good when cool, your task is complete.
In extreme situations, the wheel will not move at all even when heated and a fair pressure applied. Repairing the problem when it's this bad requires removal of the whole elnagraph. This removal can only be done by also removing the top drive shaft. Definitely not a task for an amateur. When removed, you can attend to the seized parts much more easily. Putting everything back isn't enough. You will need to ensure that the timing belt is in exactly the right spot. The star series service manual is an excellent resource here.

Slipping Hand Wheel

When you put your foot down and go nowhere or you hear that it is slipping, it will need to be repaired.
The hand wheel is driven by an intermediate rubber wheel, and over the years this friction wheel goes hard and sometimes crusty. I saw this more often in Brisbane due to the hotter and humid climate but I've seen it many times in Melbourne too. 
Repair is a good mix of easy and challenging. You must remove the friction wheel, which is the challenging part. 
Remove the hand wheel and you can see the rubber friction wheel. Press it with your fingernail. If it's good, it will give slightly and allow an impression. More likely it will be either smooth, shiny and hard or cracked and crusty looking. 
Picture taken from a later model

This photo is from a later machine, the Air Electronic. The AE is also fantastic, but the electronic speed control just makes it slightly less reliable than its immediate predecessor. The drive setup, however, is identical and made for a better photo. The SU has a large amount of solid metal body in the way, which is why you will need to remove multiple C clips.
Marked 1 is the tension clip. Remove this with long nose pliers.
Remove the C clip near where it says 2. This is difficult to reach and if you have dental type tools, choose the one that allows you to snag the c-clip to pull it towards you. Otherwise, small, bladed screwdrivers at an angle will do it. After the first C-clip, you can move the wheel's shaft and expose the second one. There are three C clips and the only one you don't need to remove is holding the wheel onto the bracket.
Once off, you do not need to seperate the wheel from the bracket. Make sure it rotates freely though.
You now resurface the wheel. You can use either a bench grinder or dremel. 
Using a grinder, choose a grinder wheel that's not too rough. A rough wheel will destroy the friction wheel. Wear eye and maybe hand protection, as the removed material will be very messy.
Hold the bracket with pliers against the rotating wheel and angle it slightly. As the surface comes off, keep stopping and check if the wheel's suface is still hard. As soon as it isn't, you can stop and reinstall the friction wheel in the machine. If you only have a dremel, attach a grinding wheel and do the same thing.
The second most common problem found with 1970s SUs is the machine stops driving the hook, or the hook timing goes out. This is caused by breaking of the pinion gear, which drives the rotating hook. The original pinion gears were made from a dark coloured plastic which go hard. Teeth break off or the gear just breaks completely. The replacement gears are white in colour and are not expensive. The 

Sunday, 22 March 2026

Late 1960s and 1970s singers

Someone gave me a Singer 9000 a few weeks ago and it gave me the idea of showing you how to replace the broken plastic gears.
In the example, a 9000, none of them were broken but one was seriously discoloured, which always meant it was very brittle. So I decided to replace just that gear.
Here it was beforehand.
and afterwards 
Now getting from the first to the second requires that you either follow the service manual (link is to service manual on scribd) exactly or you really know how both feed and hook timing work.
Tricky things are whether the securing screws are facing up or down and the present position of all shafts when the old one is removed. You need to remove both shafts to allow the release of the brown gear. I marked them by scribing but still mucked it up and had to correct everything so I'd suggest not attempting this unless you know how to reset both feed and hook timing.
In short, you need to release the back shaft mountings, both of the bobbin drive gears and the gear on the right with the belt. Marking them will make the work much easier but remember that the needle tip and feed dog sink beneath the needle plate at the same time ;-)